ABGAL Pool Covers, Thermal Covers & Rollers
Protect Your Pool, Reduce Running Costs and Spend Less Time Cleaning
A quality pool cover is one of the most valuable accessories you can add to your swimming pool.
Depending on the type selected, an ABGAL pool cover can help:
-
Reduce water loss through evaporation.
-
Retain or increase pool water temperature.
-
Reduce heating and chemical consumption.
-
Keep leaves, dirt and animals out of the pool.
-
Reduce cleaning and filtration requirements.
-
Extend the swimming season.
-
Make the pool easier and more affordable to maintain.
ABGAL manufactures a range of Australian-made pool covers designed for different pool environments, including solar covers, specialised thermal covers, fitted leaf covers and pool cover rollers.
The correct cover will depend on whether your main priority is heating, heat retention, water conservation, debris control or general pool maintenance.
ABGAL Solar Pool Covers
A Warmer Pool With Less Water and Chemical Loss
ABGAL Oasis solar covers, also commonly called solar blankets or bubble covers, float directly on the surface of the pool water.
Thousands of air-filled bubbles help create a barrier between the water and the surrounding air. The cover allows solar energy to enter the pool while reducing the heat and water that would otherwise escape from the surface.
ABGAL advises that selected Oasis solar covers can prevent up to 99.84% of evaporation and may increase pool water temperature by up to approximately 8°C under suitable conditions. Actual performance will vary depending on weather, pool location, cover use and other environmental factors.
Benefits of an ABGAL Solar Cover
Save Water
Evaporation is one of the largest causes of water loss from an uncovered swimming pool.
A correctly fitted solar cover places a physical barrier over the water surface, significantly reducing evaporation and the need to continually top up the pool.
Reduce Chemical Consumption
When water is lost through evaporation or regularly replaced with fresh water, the pool’s chemical balance is affected.
Reducing evaporation can help decrease the amount of salt, stabiliser and balancing chemicals required over time.
ABGAL recommends reviewing and potentially reducing automatic chlorinator output after installing a cover, as chlorine demand may decrease significantly when the pool is covered.
Increase Pool Temperature
Solar covers allow sunlight to enter the water while helping hold the collected heat within the pool.
This can provide:
-
Warmer swimming conditions.
-
A longer swimming season.
-
Reduced reliance on gas, electric or heat-pump heating.
-
Faster recovery after cooler nights.
Reduce Debris
Although a solar blanket is not primarily designed as a leaf cover, it can prevent some airborne dirt, insects and smaller debris from entering the water.
This may reduce cleaning time and pressure on the filtration system.
Suitable for Salt and Chlorinated Pools
ABGAL Oasis solar covers are designed for use with both saltwater and traditionally chlorinated swimming pools.
ABGAL Oasis Solar Cover Options
Oasis Premium Blue – 550 Micron
The Oasis Premium Blue is a heavy-duty solar cover with a deep blue appearance.
It is designed for pool owners seeking:
-
Excellent evaporation reduction.
-
Strong solar heating performance.
-
A durable 550-micron construction.
-
A premium appearance on the pool.
The darker blue material is designed to attract solar energy while the bubble structure helps retain heat within the water.
This is an excellent all-round option for residential outdoor pools where heating and water conservation are both priorities.
Oasis SilverBack – 550 Micron
The Oasis SilverBack has a translucent blue upper layer and a reflective silver backing.
The blue upper layer allows solar energy to enter the cover, while the silver underside is designed to assist with heat retention.
It is suitable for:
-
Heated and unheated pools.
-
Indoor and outdoor pools.
-
Residential and commercial applications.
-
Pool owners wanting a balance of solar heating and insulation.
ABGAL states that the SilverBack can prevent up to 99.84% of evaporation and is supplied with a 10-year pro-rata warranty. Warranty terms, conditions and correct-use requirements apply.
Oasis Triple Cell
The Triple Cell cover uses a specialised three-bubble design that creates a larger insulating air zone.
It is designed to provide:
-
Improved insulation.
-
Greater protection from chlorine exposure.
-
Excellent evaporation control.
-
Premium durability.
-
Strong heat-retention performance.
ABGAL states that Triple Cell covers prevent more than 99% of evaporation and are supplied with a 12-year pro-rata warranty. Warranty conditions apply.
Oasis Clarity – 400 Micron
Oasis Clarity is a highly translucent solar cover designed to allow a large amount of sunlight to pass into the pool.
It is particularly suitable for customers who want:
-
Strong solar gain.
-
A clearer appearance over the pool.
-
A lighter cover that is easier to handle.
-
Effective evaporation reduction.
Because it is highly translucent, the Clarity cover focuses strongly on allowing solar energy into the water.
Oasis 400 and Oasis 500
The Oasis 400 and Oasis 500 ranges provide practical solar-cover options for many residential pools.
The micron measurement refers to the thickness of the cover material.
Generally:
-
A thicker cover is heavier and may offer increased durability.
-
A lighter cover can be easier to handle.
-
The best selection depends on pool size, use, budget and expected service life.
ABGAL’s 400, 500 and 550-micron Oasis covers are listed as Climate Care Certified, WaterWise and Smart Approved WaterMark licensed.
ABGAL Heatshield Thermal Pool Covers
Maximum Heat Retention for Heated Pools
A standard solar cover is designed to use sunlight to help warm pool water.
A specialised thermal cover serves a different purpose. Its primary role is to hold in heat that has already been produced by a pool heating system.
The ABGAL Heatshield is designed for pools heated by:
-
Heat pumps.
-
Gas heaters.
-
Solar heating.
-
Electric heating.
-
Combined heating systems.
It is suitable for both indoor and outdoor heated pools.
How the Heatshield Thermal Cover Works
The Heatshield cover is manufactured with a closed-cell polyethylene foam core and reinforced protective outer layers.
This structure creates an insulating barrier over the water surface.
Unlike a transparent solar blanket, its main purpose is not to collect solar energy. It is designed to reduce heat transfer from the warm pool water into the cooler surrounding air.
ABGAL states that Heatshield can reduce heat loss by approximately 75% and reduce evaporation by more than 99%. Actual results will depend on the pool, climate, cover condition and how consistently the cover is used.
Benefits of a Heatshield Thermal Cover
Reduced Heating Costs
An uncovered heated pool can lose a substantial amount of heat overnight, particularly when the surrounding air is cool or windy.
By reducing heat loss, a Heatshield cover can:
-
Reduce heater operating time.
-
Help the pool reach its set temperature sooner.
-
Reduce electricity or gas consumption.
-
Improve the overall efficiency of the heating system.
-
Help maintain a more stable swimming temperature.
Reduced Evaporation
Warm water evaporates quickly when exposed to cooler air.
A thermal cover significantly reduces this evaporation, helping conserve water and reduce the need for frequent topping up.
Improved Indoor Pool Conditions
Indoor heated pools can create significant humidity and condensation.
Covering the pool when it is not in use can reduce the amount of moisture released into the building, potentially lowering demand on ventilation and air-conditioning systems.
It may also help reduce condensation-related damage to surrounding surfaces, fixtures and equipment.
Heavy-Duty Construction
Heatshield covers are manufactured from a reinforced fabric with a closed-cell foam core.
They are waterproof, UV stabilised and chemical resistant. ABGAL also describes the cover as reversible where the shape of the pool allows it to be periodically flipped.
Optional Accessories
Depending on the pool and installation, optional features may include:
-
Edge binding.
-
Wind skirts.
-
Haul cords.
-
Reinforced ends.
-
Flotation pockets.
-
Attachment harnesses.
-
Protective over-covers.
These options can be particularly useful for large residential, indoor or commercial pools.
Hinged Pool Cover Options
A Practical Solution for Irregular and Extended Pool Shapes
Hinge options can be incorporated into selected ABGAL pool covers to accommodate pools with unusual shapes or sections that extend beyond the main pool walls.
This is particularly useful where a pool includes:
-
Extended steps.
-
Wide entry areas.
-
Offset sections.
-
Irregular corners.
-
Attached spa areas.
-
Sections that project beyond the main rectangular pool shape.
The cover is manufactured as one connected piece and rolled out over the main section of the pool in the usual way.
Once the main cover has been positioned, the hinged section can then be folded outward to cover the area that extends beyond the main pool walls.
How the Hinged Section Works
The hinged panel remains attached to the main cover, allowing the entire cover to be handled and stored as one complete unit.
During use:
-
The main cover is rolled out across the primary pool area.
-
The attached hinged section is unfolded.
-
The hinged section is positioned over the extended or irregular area.
-
When removing the cover, the hinged section is folded back onto the main cover before the entire cover is rolled onto the roller.
This design avoids the need for a completely separate cover piece, which could otherwise be misplaced, handled independently or stored separately.
Benefits of a Hinged Cover Design
A hinged cover can provide:
-
Improved coverage for irregular pool shapes.
-
Easier operation than using multiple separate covers.
-
One connected cover that can be rolled and stored together.
-
Better coverage over steps, spas and extended sections.
-
A neater and more practical installation.
-
Reduced gaps around unusual pool areas.
Accurate measurements are essential when manufacturing a hinged cover to ensure the folding section aligns correctly with the pool shape and operates smoothly with the selected roller.
Our team can assess your pool layout and determine whether a hinged cover design is suitable.
ABGAL Pooltex Leaf and Debris Covers
Keep Leaves, Dirt and Animals Out of Your Pool
The ABGAL Pooltex is a fitted mesh cover designed primarily for debris control.
Unlike a floating solar blanket, a Pooltex cover is secured around the outside of the pool and held above the water using fitted attachment points.
Its fine mesh construction allows rainwater to pass through while keeping larger debris on top of the cover.
Benefits of a Pooltex Cover
Reduce Leaves and Debris
Leaves remain on top of the cover rather than sinking to the bottom of the pool.
They can then be swept or blown away before the cover is removed.
This can significantly reduce:
-
Manual vacuuming.
-
Robotic cleaner operating time.
-
Filter loading.
-
Skimmer basket blockages.
-
Organic contamination.
-
Phosphate introduction from decomposing leaves and plant material.
Reduce Pool Maintenance
Keeping organic debris out of the water helps reduce pressure on the pool’s circulation and filtration equipment.
Cleaner water may also reduce chlorine demand and make the pool easier to recover after winter or extended periods of low use.
Reduce Animal Entry
A fitted cover can help deter ducks, frogs and other animals from entering the pool.
However, no pool cover should be relied upon as a substitute for compliant pool fencing, secure gates or active adult supervision around children and pets.
Reduce Evaporation
Although a mesh leaf cover does not stop evaporation as effectively as a floating solar or thermal cover, it can still provide a meaningful reduction.
ABGAL advises that Pooltex covers can reduce evaporation by more than half.
Custom Fitted to the Pool
Pooltex covers can be manufactured to suit a wide variety of pool shapes and may be designed around features such as:
-
Spas.
-
Steps.
-
Water features.
-
Irregular pool shapes.
-
Raised walls.
-
Unique coping layouts.
Accurate measurements are essential to ensure the cover fits and operates correctly.
Pooltex Warranty
ABGAL lists the Pooltex fitted leaf cover with an eight-year pro-rata warranty. Warranty terms, installation requirements and exclusions apply.
ABGAL Leafstop Covers
Leaf Protection for Above-Ground Pools
ABGAL Leafstop covers are designed primarily for above-ground swimming pools.
The lightweight micro-mesh material keeps leaves and debris out while allowing rainwater to pass through.
The cover fits over the pool in a shower-cap style and is generally secured using a marine-grade stretch cord threaded through fitted grommets.
Leafstop covers are available for various above-ground pool shapes, including:
-
Round pools.
-
Rectangular pools.
-
Keyhole pools.
-
Teardrop pools.
-
Intex and knock-down style pools.
ABGAL recommends using pool-cover floats beneath the cover to raise the centre and create a dome. This helps prevent leaves and debris from collecting in the middle of the cover.
ABGAL Pool Cover Rollers
Make Your Solar or Thermal Cover Easier to Use
A pool cover only provides its full benefit when it is used consistently.
Without a roller, removing and replacing a large pool cover can be difficult, particularly for one person.
An ABGAL pool-cover roller allows the cover to be wound neatly onto a central tube, making it easier to:
-
Remove the cover before swimming.
-
Return the cover to the pool after use.
-
Store the cover neatly.
-
Reduce dragging and handling damage.
-
Avoid folds and creases.
-
Extend the practical life of the cover.
ABGAL advises that many residential pool covers can be removed or replaced by one person within a few minutes when used with a suitable roller.
Choosing the Correct Roller
The correct roller depends on:
-
Pool width.
-
Pool-cover size and weight.
-
Solar or thermal-cover thickness.
-
Available space around the pool.
-
Whether the roller must be fixed or mobile.
-
Residential or commercial use.
-
Manual or motorised operation.
Longer and heavier covers require a stronger roller tube to reduce bending through the centre.
A thermal cover is generally heavier than a standard bubble cover and may require a more substantial roller.
Fixed Pool Rollers
A fixed roller remains in one position at the end of the pool.
This can be suitable where:
-
There is a dedicated roller area.
-
The roller will not obstruct walkways.
-
The pool layout allows the cover to be rolled directly from the water.
-
The roller does not need to be moved after use.
Mobile Pool Rollers
Mobile rollers use castors so the roller can be moved away from the pool after the cover has been wound up.
This is useful where:
-
Space around the pool is limited.
-
The roller would otherwise block access.
-
The pool area is used for entertaining.
-
The cover needs to be stored away from the water.
ABGAL advises that many of its reels can have castors fitted initially or retrofitted later.
Commercial Pool Rollers
Large commercial pools require specialised heavy-duty equipment.
ABGAL offers commercial roller options that may include:
-
Large-diameter anodised aluminium tubes.
-
Stainless-steel frames.
-
Stainless-steel castors.
-
Twin hand wheels.
-
Roller brakes.
-
Anchoring systems.
-
Low-voltage motorised winding systems.
ABGAL lists commercial roller tube sizes up to approximately 200 mm in diameter for large installations.
Protecting Your Pool Cover While It Is on the Roller
Always Use the Protective Over-Cover
A rolled-up solar blanket must not be left exposed to direct sunlight without protection.
When the cover is rolled up, multiple layers of material are concentrated together. Heat can build up rapidly between these layers and cause permanent overheating damage, commonly called roller burn.
A reflective protective over-cover should be placed over the rolled blanket whenever it is stored outdoors.
ABGAL states that a reflective over-cover is supplied with its new reels and should always be used when the solar blanket is wound onto the roller.
Do Not Leave a Solar Cover on the Pool During High Chlorine Treatment
High chlorine concentrations can damage the cover material and shorten its service life.
The cover should generally be removed when:
-
Superchlorinating or shocking the pool.
-
Treating algae.
-
Carrying out major chemical corrections.
-
Chlorine levels are substantially above the normal operating range.
Allow the water to return to the appropriate operating range before replacing the cover.
Maintain Correct Water Balance
Poor water balance can reduce the life of a cover.
Conditions that may contribute to premature deterioration include:
-
Excessive chlorine.
-
Continually low or high pH.
-
Overheated water.
-
Incorrect chemical dosing.
-
Undiluted chemicals contacting the cover.
-
Leaving a cover exposed on hot paving or decking.
Clean the Cover Carefully
The cover may be rinsed periodically with clean water to remove dust, salt or chemical residue.
Avoid harsh scrubbing, pressure cleaning or unsuitable cleaning chemicals unless specifically approved by the manufacturer.
Which Pool Cover Is Right for You?
Choose a Solar Cover When:
-
You want to warm an outdoor pool using sunlight.
-
You want to reduce evaporation.
-
You want to reduce chemical consumption.
-
You want a practical everyday cover.
-
You want a cover that can be easily used with a roller.
Choose a Heatshield Thermal Cover When:
-
Your pool is heated.
-
Heat retention is more important than solar gain.
-
You operate a heat pump, gas heater or other heating system.
-
You want to reduce overnight temperature loss.
-
You have an indoor heated pool.
-
You want to minimise heating and ventilation costs.
Choose a Pooltex Leaf Cover When:
-
Your pool is surrounded by trees.
-
Leaves and organic debris are your main problem.
-
The pool is unused for extended periods.
-
You want to reduce winter cleaning.
-
Ducks, frogs or other animals regularly enter the pool.
-
You need a fitted cover for an irregular pool shape.
Choose a Leafstop Cover When:
-
You have an above-ground pool.
-
You need an affordable debris cover.
-
You want a lightweight shower-cap style design.
-
You want rainwater to pass through the cover.
Add a Roller When:
-
You want the cover to be used consistently.
-
The cover is too large or heavy to handle manually.
-
One person needs to operate the cover.
-
You want to reduce wear caused by dragging or folding.
-
You want a cleaner and more organised pool area.
Measuring Your Pool Cover
Correct measurements are essential when ordering a pool cover or roller.
Measurements may include:
-
Maximum pool length.
-
Maximum pool width.
-
Step dimensions.
-
Spa dimensions.
-
Pool shape.
-
Location of handrails or ladders.
-
Raised walls or water features.
-
Roller position.
-
Available clearance around the pool.
For irregularly shaped pools, additional measurements or a detailed pool plan may be required.
Custom manufacturing charges may apply for unusual shapes, cut-outs or specialised fittings.
Professional Supply and Advice
Selecting the correct cover is about more than choosing a colour or thickness.
We can help assess:
-
The type and size of your pool.
-
Whether the pool is heated.
-
Your surrounding environment.
-
Leaf and debris load.
-
Pool usage.
-
Available roller space.
-
Preferred cover weight.
-
Budget and expected durability.
-
Residential or commercial requirements.
Our team can recommend an appropriate ABGAL cover and roller combination to suit your pool and how you use it.
Request a Quote
Contact us with your pool measurements, photographs and preferred cover type.
We can assist with:
-
ABGAL solar covers.
-
Heatshield thermal covers.
-
Pooltex fitted leaf covers.
-
Leafstop above-ground covers.
-
Residential pool-cover rollers.
-
Heavy-duty and commercial rollers.
-
Replacement covers.
-
Roller accessories and protective over-covers.